HP Photosmart 935 LCD Screen Replacement

Written By: Nick Oleskowicz
  • Comments: 1
HP Photosmart 935 LCD Screen Replacement

Difficulty

Moderate

Steps

17

Time Required

20 - 30 minutes

Introduction

The purpose of this guide is to teach reader to install a new LCD screen. If the current LCD screen is broken or cracked, this guide will help the reader to replace it with a new one.

  1. pcUmacIwYDEKaeKJ
    pcUmacIwYDEKaeKJ
    vhLIWCAVkl1jaFww

    • Flip the camera over so the bottom of the camera is facing you.

    • Turn the mode dial to the OFF position.

  3. EqOxGSDrkZKj1VRR
    EqOxGSDrkZKj1VRR
    TNSOidZtgfwg3wTM

    • Slide the bottom cover in the direction of the arrow to open it.

  4. M3nae2bVbub2r5CO

    • Pull out the batteries.

  5. 4l3B1wiQVUUnt24e

    • Use a Phillips #00 screwdriver to remove the two 4.7 mm screws in the bottom of the plastic casing.

  6. EtUv1xytV3EHFDW6
    EtUv1xytV3EHFDW6
    1rAiJRqw4DpUgHCR

    • Remove the four 4.7 mm screws on the left side of the camera.

  7. BW1nqe1eK3BEhBg1
    BW1nqe1eK3BEhBg1
    CPFkySUkhsRYZmfU

    • Remove the four 4.7 mm screws on the opposite side of the camera.

  8. GFCuVopd1cukUFvO
    GFCuVopd1cukUFvO
    WGVFniuVGCD4pX2a
    W4QkWtLS6Pchm1ER

    • Use your thumbs to pry the case apart.

    • It is easiest to pry the case apart if you start at the bottom.

    • The case should come apart with minimal effort. If it doesn't, you can use a spudger or plastic opening tool to pry it open.

  9. 5ShJH21JHb2n2aSa

    • This step requires a significant amount of force.

    • Pull the bottom half of the inner camera out of the case by half an inch. This may be difficult.

  10. TQQlM5ipUoRaOBUZ
    TQQlM5ipUoRaOBUZ
    JYiNvCPXvMwlgAGi

    • While pulling the camera out of the case, note the small soft plastic cover on the side. This cover will detach from the rest of the device.

    • Once the bottom of the inner camera is pulled out, pull the device out completely.

    • Use a firm grasp when removing the device from the case for stability and control.

  11. pORbmX6kK2IZjyBq

    • Orient the camera so that the LCD screen is facing you.

    • If case is still on, remove it by following the Plastic Casing Installation Guide found in the previous steps.

    • Removing the casing completely is crucial to completing this guide.

  12. RCSvGUjKrY5y3BAl
    RCSvGUjKrY5y3BAl
    1ZJ31fiYVMntVQnc

    • Using a Phillips #00 remove the four 4.40 mm screws that secure the LCD screen to the frame.

  13. 3KtAQYbkgwW1G2nm

    • Allow the LCD screen to flip down. This will expose the electric strip that connects the screen to the camera.

  14. JQepbYBwNTW2e4uQ

    • Look for where the yellow electric strip is attached to the camera. You will find a plastic grey bar and a white base holding this strip in place.

    • Push the grey bar away from the white base. This will release the yellow electric strip and free the LCD screen from the camera.

  15. MvPTgBQ2hVQOAZG3

    • Unplug the connected red and white wires. They will come out with the small white casing.

  16. Clr3McPRhLeEErpi

    • Flip camera so that the lens is facing away from you. You should be looking at the LCD screen.

  17. hlAePlpNAntse365
    hlAePlpNAntse365
    Kds6lXNOZTQGwViu

    • Remove the bottom left LCD mounting frame screw. The screen should come loose after the screw is removed.

    • Remove the LCD screen from the camera. Make sure that the electric strip comes out with screen.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Nick Oleskowicz

Member since: 04/04/12

299 Reputation

One comment

Thank for this very good job, I own this this camera so it is will be quite easy to fix it following your guide.

Saverio Mercurio -